View LTL17KCBH5D-0Q1A_9044323.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL17KCBH5D-0Q1A spec no.: ds20-2016-0057effective date: 07/08/2016revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
1 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a through hole lamp ltl17kcbh5d - 0q1a rev description by date p 0 01 preliminary spec ( rdr - 20160474 - 02 ) norah 4 / 19 /201 6 p002 update packing spec. on page 6 norah 5/30/2016 above data for pd and customer tracking only - nppr received a nd upload on opnc nareerat 6/2/2016
2 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 1. description through hole leds are offered in a variety of packages such as 3mm, 4mm, 5mm, rectangular, and cylinder which are suitable for all applications requiring status indicati on. several intensity and viewing angle choices are available in each color for design flexibility. 1 . 1. features ? low power consumption & high efficiency ? lead free & rohs compliant ? popular t - 1 diameter ? ingan blue 470 nm with blue diffused lens 1.2 . appl ications ? communication ? computer ? consumer ? home appliance ? industrial 2 . outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted. 3. protruded resin under flange is 0.5 mm (.0 2 ") max. 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without notice.
3 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 3. absolute maximum ratings at ta = 25 c parameter maximum rating unit power dissipation 108 mw peak forward current (duty cycle Q 1/10, pulse width Q 10ms) 100 ma dc forward current 30 ma derating linear from 3 0 0.5 ma/ operating temperature range - 30c to + 80 c storage temperature range - 40 c to + 100 c lead soldering temperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. ele ctrical / optical characteristics at ta=25 c parameter symbol min. typ. max. unit test condition luminous intensity iv 180 240 880 mcd if = 20ma note 1,5 viewing angle 21/2 50 deg note 2 (fig.6) peak emission wavelength p 468 nm measuremen t @peak (fig.1) dominant wavelength d 46 0 470 475 nm note 4 spectral line half - width ? 2 2 nm forward voltage vf 2. 7 3.2 3.6 v if = 20ma reverse current ir 100 a vr = 5v (note 6) note: 1. luminous intensity is measured with a light sen sor and filter combination that approximates the cie eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the dominant wavelength , d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 5. iv guarantee must be included with 15% testing tolerance. 6. reverse voltage (vr) condition is applied for ir test only. the device is not designed for reverse operation.
4 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 5. typical electrical / optical characteristics curves (25 c ambient temperature unless otherwise noted)
5 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 6 . taping features * compatible with radial lead automatic insertion equipment. * most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * folding packaging simplifies handling and testing. * reel packaging is available by removing suffix a on option. * ammo packing series lamp type 24 led+gap. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 4.8 0. 188 5.8 0. 228 front to rear deflection h -- -- 2.0 0.078 height of seating pla ne h 18.0 0. 709 19.0 0. 748 feed hole to bottom of component h1 20.0 0. 787 22.0 0 . 827 feed hole to overall component height h2 2 5.1 0.9 88 2 7. 7 1. 091 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead locatio n p1 3.15 0.124 4.55 0.179 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748
6 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 7. packing spec. total 3,0 00pcs per inner carton n on - full packing 2,0 00pcs or 1,000pcs per inner carton 10 inner cartons per outer carton t otal 30 ,000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing
7 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 8. bin table speci fication luminous intensity unit : mcd @ 20 ma bin code min. max. hj 180 310 kl 310 520 mn 520 880 note: tolerance of each bin limit is 15% dominant wavelength unit : nm @ 20 ma bin code min max b07 460.0 465.0 b08 465.0 470.0 b09 470.0 47 5.0 note: tolerance of each bin limit is 1nm
8 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 9 . cautions 9 . 1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 9 . 2. storage the storage ambient for the leds should no t exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original packaging are used within three months. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed cont ainer with appropriate desiccant or in desiccators with nitrogen ambient. 9 . 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the leds if necessary. 9 . 4. lead forming & assembly during lead forming, the leads should be ben t at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 9 . 5. soldering when soldering, leave a minimum of 2 mm clearance from the base of the lens to t he soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during s ol dering while the led is at high temperature. r ecommended soldering conditions : soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2 mm from the base of the e poxy bulb pre - heat pre - heat time solder wave soldering time dipping position 100c max. 60 seconds max. 260c max. 5 seconds max. no lower than 2 mm from the base of the epoxy bulb note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led. ir reflow is not suitable process for through hole type led lamp product. 9 . 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds c onnected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model ( a ) circuit model ( b ) (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds. led led
9 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 9 .7. esd (electrostatic discharge) static electr icity or power surge will damage the led. suggestions to prevent esd damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing suggested checking list : training and certification 9 .7. 1 .1 . everyone working in a static - safe area is esd - certified? 9 .7.1. 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 9 .7.2.1 . static - safe workstation or work - areas have esd signs? 9 .7. 2 . 2. all surfaces and objects at all static - safe workstation and within 1 ft measure less than 100v? 9 .7.2. 3. all ionizer activated, positioned towards the units? 9 .7.2. 4. each work surface mats grounding is good? personnel grounding 9 .7.3.1 . ev ery person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 9 .7.3.1 . if conductive footwear used, conductive flooring also present where operator stand or walk? 9 .7.3 .2 . garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 9 .7.3.3 . every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 9 .7.3.4 . all wrist strap or heel strap checkers calibr ation up to date? note: *50v for blue led. device handling 9 .7.4. 1. every esds items identified by eia - 471 labels on item or packaging? 9 .7.4. 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 9 .7.4. 3. no static charge generators (e.g. plastics) inside shielding containers with esds items? 9 .7.4. 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 9 .7.5. 1. a udit result reported to entity esd control coordinator? 9 .7.5. 2. corrective action from previous audits completed? 9 .7.5. 3. are audit records complete and on file?
10 / 10 part no. : ltl17kcbh5d - 0q1a bns - od - fc002/a4 through hole lamp ltl17kcbh5d - 0 q 1a 10 . reliability test classification test item test condition sample size refere nce standard endurance test operation life ta = u nder room t emperature if = per datasheet maximum drive current test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1026 (1995) mil - std - 883g:1005 (2006) high temperature high humidity storage t a = 60 c rh = 90 % test time= 24 0hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 202g:103b (2002) jeita ed - 4701:100 103 (2001) high temperature storage ta= 105 5 c test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1031 (1995) mil - std - 883g:1008 (2006) j eita ed - 4701:200 201 (2001) low temperature storage ta= - 55 5 c test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) jeita ed - 4701:200 202 (2001) environmental test temperature cycling 100 c 25 c - 40 c 25 c 30mins 5mins 30mins 5mins 3 0 cycles 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1051 (1995) mil - std - 883g:1010 (2006) jeita ed - 4701:100 105 (2001) jesd22 - a104c (2005) thermal shock 100 5 c - 30 c 5 c 15mins 15mins 3 0 cycles (<20 secs transfer ) 22 pcs (cl=90%; ltpd=10 %) mil - std - 750d:1056 (1995) mil - std - 883g:1011 (2006) mil - std - 202g:107g (2002) jesd22 - a106b (2004) solder resistance t.sol = 260 5 c dwell time= 101 seconds 3mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil - std - 750d:2031(1995) jeita ed - 4701: 300 302 (2001) solderability t. sol = 245 5 c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil - std - 750d:2026 ( 1995) mil - std - 883g:2003 (2006) mil - std - 202g:208h (2002) ipc/eia j - std - 002 (2004) soldering iron t. sol = 350 5 c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil - std - 202g:208h (2002) jeita ed - 4701:300 302 (2001) 1 1 . others the appe arance and specifications of the product may be modified for improvement, without prior notice.

▲Up To Search▲

Price & Availability of LTL17KCBH5D-0Q1A

	To Download LTL17KCBH5D-0Q1A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .